All American Products Co.

Back

TOOLING COMPONENTS 
TYPICAL TORQUE-OUT AND TENSILE LOADS
All tests run with bolt thread of sufficient length to insure full thread engagement of insert. Torque-out was
determined using a torque wrench on a bolt in conjunction with a bushing. The bushing's maximum outside diameter
was in all cases less than the insert outside diameter, thus only pure torque was recorded, not clamp-up. 
Torque-out was recorded at the point the insert rotated relative to the parent material. Tensile (pull-out) was
determined using a 20,000 lb. Baldwin Southwark tensile machine. Load was applied until the first indication of
insert movement was noted; at this point the pull-out value was recorded.
NOTE: The minimum distance that an insert can be installed relative to the edge of a material is dependent upon
the characteristics and type of print material involved. Most materials will require one (1) times the insert O.D.
for edge distance, as measured from the center of the installation hole. However, this can vary with material.

E-Z LOK

TYPICAL TORQUE-OUT AND TENSILE LOADS

MATERIAL TRADE NAMES

LEXAN

ZYTEL
NYLON

GLASS FILLED
EPOXY (GEE)

GLASS FILLED
EPOXY (GEB)

PHENALIC-PAPER COMP.
LAMINATE

"GLASTIC" GLASS
REINFORCED
PLASTIC

P/N

MATE-
RIAL

SIZE

HOLE
SIZE

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

TORQUE
-OUT
IN
LBS.

TENSILE
LBS.

652-03

BRASS

 (4-40)

.156

14

80

22*

69

18

140

19*

180

10

100

11

105

652-03 

BRASS

 (4-40)

.158

13

69

14

57

15

117

14

139

-

-

-

-

652-03 

BRASS

 (4-40)

.160

6

40

6

32

10

70

9

80

-

-

-

-

652-03 

BRASS

 (4-40)

.162

5

20

4

14

7

33

6

64

-

-

-

-

652-03 

CRES

 (4-40)

.156

14

82

22*

71

20*

145

19*

182

-

-

-

-

652-03

CRES

 (4-40)

.158

12

70

14

60

15

120

13

140

-

-

-

-

652-03 

CRES

 (4-40)

.160

7

35

8

35

11

70

9

85

-

-

-

-

652-03 

CRES

 (4-40)

.162

5

16

5

15

8

29

6

60

-

-

-

-

652-04

BRASS

 (6-32)

.188

30

85

30

100

42*

230

45*

240

22

240

20

210

652-04 

BRASS

 (6-32)

.190

24

75

25

90

38

180

37

235

-

-

-

-

652-04

BRASS

 (6-32)

.192

13

50

15

17

19

170

22

150

24

210

24

200

652-04

BRASS

 (6-32)

.194

6

40

8

65

13

160

17

120

10

165

-

-

652-04

CRES

 (6-32)

.188

30

93

30

122

42*

262

45*

240

-

-

-

-

652-04 

CRES

 (6-32)

.190

20

80

20

110

34

205

33

235

-

-

-

-

652-04

CRES

 (6-32)

.192

15

70

16

90

21

195

24

145

-

-

-

-

652-04

CRES

 (6-32)

.194

10

50

12

75

14

180

21

125

-

-

-

-

652-05

BRASS

 (8-32)

.219

40

180

40

210

85*

300

85*

280

41

230

45

230

652-05

BRASS

 (8-32)

.221

35

178

35

200

70

273

75*

208

-

-

-

-

652-05

BRASS

 (8-32)

.223

22

130

25

160

51

235

72*

190

-

-

-

-

652-05

BRASS

 (8-32)

.225

15

80

16

110

43

132

67*

165

-

-

-

-

652-05

CRES

 (8-32)

.219

30

190

35

220

75

310

85*

281

-

-

-

-

652-05 

CRES

 (8-32)

.221

25

145

30

175

60

240

75*

200

-

-

-

-

652-05

CRES

 (8-32)

.223

15

70

20

100

44

175

72*

192

-

-

-

-

652-05

CRES

 (8-32)

.225

14

50

18

80

42

102

65

165

-

-

-

-

652-06

BRASS

(10-32)

.250

80

240

82

375

90*

420

110*

420

75

420

80

450

652-06 

BRASS

(10-32)

.252

45

172

54

250

66

320

110*

405

-

-

-

-

652-06

BRASS

(10-32)

.254

27

105

26

160

38

175

110*

300

-

-

-

-

652-06

BRASS

(10-32)

.256

18

30

20

132

22

150

105

205

-

-

-

-

652-06

CRES

(10-32)

.250

85*

250

85

420

90*

510

110*

490

-

-

-

-

652-06 

CRES

(10-32)

.252

59

220

61

265

76*

460

107

425

-

-

-

-

652-06

CRES

(10-32)

.254

31

122

32

175

41

310

111*

257

-

-

-

-

652-06

CRES

(10-32)

.256

25

42

21

140

24

280

105

240

-

-

-

-

 
*BOLT BROKE

  Drill Bushings  Tooling Components  Toggle Clamps 
Back  Receive Literature  Home Page

All American Products Co.
 1135 Aviation Pl., P.O. BOX 190, San Fernando, CA 91340
Tel.: (818) 361-0059, Fax: (818) 898-2236
E-Mail Address: sales@allamericanproducts.com

Copyright (c)1996-2003 All American Products Co. All Rights Reserved.