All American Products Co.

Back

TOOLING COMPONENTS

DETENT RING PIN SPECS

NOMINAL PIN
DIAMETER
(A)

DIAMETER TOLERANCES
BEFORE PLATING
COLD FINISHED ROUNDS

PULL RING
DIAMETER
(INCHES)

END CHAMFER
LENGTH x 15°
(INCHES)

+.000
-.040
B
(INCHES)

CARBON STEEL
ZINC PLATED *

STAINLESS STEEL **

3/16

.1855-.1875

.1865-.1885

7/8

0.078

0.234

1/4

.2480-.2500

.2490-.2510

1

0.094

0.281

5/16

.3105-.3125

.3110-3140

1

0.125

0.344

3/8

.3730-.3750

.3735-.3765

1

0.141

0.391

7/16

.4355-.4375

.4360-.4390

1

0.156

0.438

1/2

.4980-.5000

.4980-.5020

1-1/4

0.172

0.484

5/8

.6230-.6250

.6230-.6270

1-1/4

0.188

.500 or .562

3/4

.7480-.7500

.7480-.7520

1-1/2

0.188

.563 or .625

Unless otherwise noted, all dimensions are for reference only.

* Plating will typically add .0002 to .0005 inches to diameter.

DETENT RING PINS - ZINC PLATED

P/N

STOCK SIZES
(DIAMETER X
EFFECTIVE LENGTH)

APPROXIMATE
WEIGHT/POUNDS
PER 100 PIECES

BALL
DIAMETER

MAXIMUM
BALL HEIGHT
ABOVE SHANK

BALL
COMPRESSION
LOAD, LBS.***

184-00

3/16 x 13/16

1.50

3/32

0.028

4-7

184-01

3/16 x 1

1.65

184-02

3/16 x 1-5/16

1.90

184-03

3/16 x 1-1/2

2.04

184-04

3/16 x 1-13/16

2.30

184-05

3/16 x 2

2.43

184-06

1/4 x 3/4

2.20

1/8

0.038

7-11

184-07

1/4 x 1

2.56

184-08

1/4 x 1-1/4

2.90

184-09

1/4 x 1-1/2

3.25

184-10

1/4 x 1-3/4

3.60

184-11

1/4 x 2

3.95

184-12

1/4 x 2-1/4

4.30

184-13

1/4 x 2-1/2

4.64

184-14

1/4 x 2-3/4

5.00

184-15

1/4 x 3

5.34

184-16

5/16 x 5/8

3.30

5/32

0.047

10-14

184-17

5/16 x 3/4

3.59

184-18

5/16 x 1

4.14

184-19

5/16 x 1-1/8

4.40

184-20

5/16 x 1-1/2

5.22

184-21

5/16 x 1-5/8

5.50

184-22

5/16 x 2

6.31

184-23

5/16 x 2-1/8

6.50

184-24

5/16 x 2-1/2

7.40

184-25

5/16 x 3

8.49

184-26

5/16 x 3-1/8

8.70

184-27

3/8 x 5/8

4.14

3/16

0.056

14-18

184-28

3/8 x 3/4

4.53

184-29

3/8 x 1

5.31

184-30

3/8 x 1-1/8

5.71

184-31

3/8 x 1-1/2

6.88

184-32

3/8 x 1-5/8

7.29

184-33

3/8 x 2

8.44

184-34

3/8 x 2-1/8

8.84

184-35

3/8 x 2-1/2

10.01

184-36

3/8 x 2-5/8

10.40

184-37

3/8 x 3

11.57

184-38

3/8 x 3-1/8

11.96

184-39

7/16 x 1

7.66

7/32

0.066

14-18

184-40

7/16 x 2

11.92

184-41

7/16 x 2-1/16

12.20

184-42

7/16 x 2-1/2

14.04

184-43

7/16 x 2-9/16

14.30

184-44

7/16 x 3

16.18

184-45

1/2 x 1/2

7.40

1/4

0.075

16-20

184-46

1/2 x 1

10.10

184-47

1/2 x 1-1/2

12.90

184-48

1/2 x 2

15.70

184-49

1/2 x 2-1/2

18.50

184-50

1/2 x 3

21.30

184-51

5/8 x 1

17.30

1/4

0.075

20-25

184-52

5/8 x 1-1/2

21.80

184-53

5/8 x 2

26.00

184-54

5/8 x 3

34.70

184-55

5/8 x 4

43.40

184-56

3/4 x 1

25.90

3/8

0.100

20.25

184-57

3/4 x 2

33.00

184-58

3/4 x 2-1/2

42.00

184-59

3/4 x 3

52.50

184-60

3/4 x 3-1/2

63.00

184-61

3/4 x 4

68.00

*** Ball Compression Load is the force required to compress ball flush to shank.

 Drill Bushings  Tooling Components  Toggle Clamps 
Back  Receive Literature  Home Page

All American Products Co.
1135 Aviation Pl., P.O. BOX 190, San Fernando, CA 91340
Tel.: (818) 361-0059, Fax: (818) 898-2236
E-Mail Address: sales@allamericanproducts.com

Copyright (c)1996-2003 All American Products Co. All Rights Reserved.